This post wraps up a series describing the construction of a 200W Class D AM transmitter for 160m, built, tested and put on air over 6 months from August 2019. The transmitter consists of a digital PLL VFO and driver circuit, an Arduino controller, a microphone amplifier, a Pulse Width Modulator, two H-bridge Class D RF modules each capable of at least 100 watts of carrier, an RF power combiner, Low Pass Filter, a 300W power supply and a switching regulator. At the Australian legal limit of 120W carrier, all parts of the transmitter run cool due the use of switching designs. Previous posts describe the switching regulator, 300 watt DC power supply and dummy loads for this project.Continue reading
QRP By The Bay is a regular meet-up of amateur radio operators, makers and experimenters , Chelsea Beach, Melbourne. On Saturday 8th February the weather was summery, a warm 28 degrees C, but windy, 35km/h blow from the south-east. A strong turn out resulted in lots of conversation, show-and-tell, and general story telling. The video shows some of the faces and activity. If you want to know more about any of the people or projects drop a comment below.
I was expecting Peter VK3YE to take his wade-tenna into the shallows for some pedestrian mobile contacts, but the wind made that option risky. No matter, there was plenty to see and discuss at the tables.
Thanks to Peter VK3YE for continuing this series of ‘eyeball’ QSOs, a now regular and much appreciated date on the amateur radio calendar in Melbourne.
Amplitude Modulation holds a fascination for me. It dates back to those hours spent as a teenager listening to the big broadcast-like amateur AM stations in the 1970s and 80s, on 160, 80 and 40 meters. Signals that seemed as wide and loud as medium wave commercial broadcast stations, bearing sonorous, paced voices that projected a wealth of wisdom and experience, and in many cases, a grandfatherly manner. Back then, AM was known as ‘The Gentleman’s Mode’.Continue reading
On the 25th October 2019 I dragged David VK3KR out to the Yarra Ranges for some SOTA fun. The story is told by the video. Thanks to all chasers!
QRP By The Bay was held again at Chelsea Beach on Saturday 2nd November 2019. A crowd of QRP, homebrew enthusiasts, and amateur radio knockabouts gathered on a wet and windy day, some with show-and-tell items, some obviously shy of bringing a full scale portable station on account of what the unpredictable weather might do.Continue reading
My Pulse Width Modulated AM transmitter project required dummy loads to match the load impedance of the RF power stage (50 ohms) and the Pulse Width Modulator (12 to 16 ohms). Surely any self-respecting amateur radio station would have a decent 50 ohm dummy load, I hear you ask incredulously. I do have one at VK3HN … or I did.Continue reading
This post describes construction of a 300 watt DC power supply for use in a 150 watt Class D AM transmitter. The transmitter design calls for about 150 volts DC at 2 amps continuous and up to 4 amps peak. This post describes the 240v mains DC supply. The switch mode regulator is described in another post. The other modules in this QRO transmitter project are to follow.Continue reading
Laurie VK3SJ is an accomplished RF designer and homebrewer in Melbourne’s 160m scene. You can hear his excellent AM signal regularly on the 160m AM Coffee Break net most weekdays. Laurie has spent a great deal of time experimenting with Class D, E and Pulse Width Modulators. He has an interesting Class D AM transmitter design with a pulse width modulator. Laurie’s design has been built by Wayne VK3ALK, who I met online in the Class E Forum on AMFone. After lots of emails and a few calls with these homebrew AM experts, I decided to proceed with my build of a VK3SJ AM transmitter for 160m.Continue reading
After a few months of operating my FAT5 160m AM Class E transmitter with its linear modulator, it was time to try Dave and Eric’s Pulse Width Modular module (PuWMa). This is a PWM using the Texas Instruments’ UCC25701 PWM chip, with TC4421 drivers and IRF640 switching FETs, followed by the obligatory Low Pass Filter to clean the 170kHz AC off the modulated DC.Continue reading
Ham Radio Blog of VK2KMI
A passionate amateur looks at Melbourne history
My journey of repairing and recycling anything I put my hands on that I believe is still useful. Not just hardware, but including software with relevant content and issues in the field of Cyber Security, Vulnerability Scanning and Penetration Testing.
Radio craft, homebrew, QRP/SOTA, AM
Amateur radio experiences with VK1DA
Bits of technology and illogic by WA2MZE
This blog is no longer in use!